Terminal Block Three Phase Filter Low Pass EMI/RFI Filter For Servo
Motor
Terminal Block Three Phase Filter:
YX83G3-30A-T is the three phase filter.High reliability designed
for industrial equipment usage with Three-phase Three-wire filter
or Three-phase Four-wire filter. Various screw terminals output for
different amps is designed for easy installation. Typical
applications in testing and measuring equipment, automation
equipment, servo drives, lighting, telecom equipment, frequency
inverters, motor drives and so on.
Features Of Three Phase Filter:
1. Good noise attenuation in both forward and reverse directions
for common mode and normal mode.
2. High reliability designed for industrial equipment usage with
3-Phase 3-Wire and 3-Phase 4-Wire.
3. The rated current can be offered from 10 to 20 amps.
4. Various screw terminals output for different amps is designed
for easy installation.
5. Custom-specific versions are available on request.
Technical Specification:
- Rated Voltage: 250/440VAC
- Rated Currents: 10A ~ 200A
- Operating Frequency: 50/60Hz
- Hipot Rating (Line-to-Line): 1450VDC
- Hipot Rating (Line-to-Ground): 2250VDC
- Operating Temperature: -25 ~ +85°C
- Safety Compliance: CE
Filter Selection Table:
| Part No. | Case | Rated Currents (A) | Output Connections |
| YX83G3-10A | G3 | 10 | Fast-on terminal |
| YX83G3-15A | G3 | 15 |
| YX83G3-20A | G3 | 20 | Wire |
| YX83G3-30A | G3 | 30 |
| YX83G3-40A | G3 | 40 | M4 Screw/M6 Screw |
| YX83G3-50A | G3 | 50 |
*Q: Fast-on 6.35x0.8mm 
S: Screw
lug 
T: Terminal block
Naming Rule:
| YX | 83 | G3 | - | 30 | - | T |
| ∣ | ∣ | ∣ | | ∣ | | ∣ |
| Three Phase | Circuit | Dimension | | Current | | Output Connection |
| | 83:83 circuit | G3 | | 10A :10 amp | | Q:fast-on tab 250 |
| | | | | 20A :20 amp | | S:M4 screw |
| | | | | 30A :30 amp | | T:Terminal block |
YX83G3-30A-T Filter Picture:
Electrical Schematic:
Mechanical Dimension(Unit: mm)
| Case | A | B | C | D | E | F | G | H | I | J | K | L | M |
|
| G1 | 72 | 65 | 39 | 75 | 85 | 35 | 22 | | 45 | M4 | M4/M6 | | |
|
| G2 | 98 | 80 | 40 | 95 | 105 | 50 | 20 | 4.5*6.5 | 50 | M4 | M4/M6 | | |
|
| G3 | 120 | 100 | 50 | 115 | 130 | 50 | 28 | 4*6 | 60 | M4 | M4/M6 | | |
|
| G4 | 200 | 127 | 80 | 150 | 170 | 62 | 49.5 | 6*9 | 117 | M6/M8 | M8/M10 | | |
|
| G5 | 150 | 105 | 60 | 120 | 135 | 55 | 35 | 4*6 | 90 | M6 | M8 | | |
|
| G6 | 260 | 170 | 100 | 196 | 220 | 85 | 65 | 8*12 | 172 | M8 | M10 | | |
|
| Tolerances | ±1 | ±1 | ±1 | ±0.15 | ±1 | ±0.5 | ±0.5 | ±0.15 | ±0.15 | | ±0.15 | ±0.15 | ±2 |
|
